Submit Hint Search The Forums LinksStatsPollsHeadlinesRSS
14,000 hints and counting!


Click here to return to the 'I'm about to do this' hint
The following comments are owned by whoever posted them. This site is not responsible for what they say.
I'm about to do this
Authored by: DelVach on Mar 09, '04 02:42:52PM
I've got a Beige G3 266 MT that I'm gearing up to install OS X on- just need a hard drive. Since this seems like the right thread, and I haven't even properly googled the subject yet, this seems like a good thread to ask for advice, pitfalls, useful links, etc. Basically:
  • Has a NewerTech G4/400 Ziff upgrade, but I still have the original G3
  • I'm going to install a 60Gig drive (from my LaCie Firewire drive, which will be getting a new 160+), partitioned of course
  • Has a MacAlly USB card (But I still have the original serial keyboard & mouse)
  • Has Radeon (first PCI Mac version), but original on-board video should still work (also have a Rage Orion sitting around)
So without trying to sound TOO lazy, any advice? I'm not too bad with basic hardware wrangling, but the last time I tried to get X on the system was probably 10.1, and I've tried to block it out.

[ Reply to This | # ]
I'm about to do this
Authored by: blgrace on Mar 09, '04 06:37:51PM

I have a Beige G3 Desktop with a Powerlogix 500mhz ZIF upgrade, 384mb ram, PCI USB and 100/10 Ethernet cards installed.

The only way I have been able to install Jaguar (and I've done this a few times now after stupidly experimenting with 10.2.8 upgrade and trying to install CUPS software) is to pull out all but one ram stick and both the USB and Ethernet cards. Trying to boot from my SCSI burner just didn't work.

So my advice - pull out all you PCI cards, leave only one stick of ram in, disconnect all SCSI devices and Jaguar will install happily.

The only glitch I had recently was after hosing my system by trying to install CUPS again (to see if I could get a printer working) , was that upgrading to 10.2.6 caused a crash (The grey Japanese screen of death with the "Please restart your computer by holding down the power key" message. This left the update unsuccessful and caused instability. I had to delete the 10.2.6 receipt in /Library/ Receipts and reinstall the 10.2.6 upgrade to properly complete the upgrade.

If you value your sanity, avoid the temptation to go to 10.2.8 and forget about Panther. I haven't used XPostFacto, Version 3.0a14 is available but it states on the developer's site that inbuilt video on the Beige G3 is not supported under Panther.

Phew..... so have fun :-)

oh p.s if you use Roxio Toast and you have an external SCSI burner and start getting BUS RESET errors when trying to burn CDs , save yourself some angst by changing SCSI cables - don't look for software/driver answers.



[ Reply to This | # ]
I'm about to do this
Authored by: gdiddy on Mar 10, '04 09:10:36AM

Make sure you partition your 60gig and install your system stuff into the first 8gigs. So partition your drive 8gig/52gig.

I have found that Lite-On it drives seem to work for installing OS X on my beige bomber. I purchased a Norcent 52/36/52 drive at Best Buy for 19.99 (after rebates) Works flawlessly!. I had gone through many different attempts at installing OS X on this machine - Removing G4 upgrade processor, firewire card, ram hard drive, zap pram etc. EVERYTHING! Always went to the black screen. I can now install OS X with all of these upgrades in place - and fast as hell! 52 speed vs. 8 speed with my old apple drive.

I would suggest everyone pick up a CDRW made by Lite-On It.

Check here - http://forums.xlr8yourmac.com/drivedb/search.drivedb.lasso -

for tips and hints on drive compatibilities.



[ Reply to This | # ]
I'm about to do this
Authored by: greyhawk on Mar 11, '04 01:58:08AM

I have had various sucess/failure depending on the Beige system. I have a MT with a G4/466, a Raedon 7000, and an Orange FireWire/USB2, and a G3/266 DT, and a G3/300 DT. I spent several attempts to load a fresh Jag install on the 266DT, as I was having lockups without warning, and seemingly without reason. I never could get that system working consistently, even after the following process, which worked on the G3/300.

I built a clean Jag install on a firewire disk (using a TiBook), then used BootCD creator to build a boot CD with CarbonCopyCloner on it. This is where it got interesting, I had to do a 10.2 base install on the G3 internal disk (presumably to install something into the disk), and only after that I could boot from my built CD and Clone the firewire disk onto the G3 internal disk. Just booting from the CD and Cloning the firewire disk didn't work. It's been fine ever since, even installing the Software Updates as they have come out. It's my iTunes music server.

I'd still like to know what was (is) causing the freezes. The 266DT still freezes, even without any cards, and only one 256MB stick. (Yes, I completely reformatted the HD)



[ Reply to This | # ]